Contact Us

Use the form on the right to contact us.

You can edit the text in this area, and change where the contact form on the right submits to, by entering edit mode using the modes on the bottom right. 

The Boat Yard, Treeve Lane
Hayle, TR27 5BN
United Kingdom

01736757632

Treeve Boats is a traditional working boatyard based in Hayle, Cornwall.

Treeve DS18

Treeve DS18

The Treeve DS18 is a development of the successful Cove Boat 16 and provides a natural link between this and the DS20. As such it combines the heavy load carrying capacity of the 16 with the proven sea-keeping of the 20.

The designer Denis Swire C.End, FRINA has given the DS18 a soft forefoot, a clean sweep across the full bilges and ample deadwood aperture, enabling a positive grip for the propeller and the extra wide 1.85m (6'2") Transom is try suited to net carrying.

The DS18 has also been recognised as the first boat of its type to be totally environmentally dual purpose in terms of propulsion, being able to sail at its maximum design speed whether driven by motor or sail.

The Treeve DS18 has established itself as a reliable and easily driven heady duty workboat. The shallow 0.6m (2') draught enables the DS18 to operate from drying harbours, beaches and coves, while the ability to use minimum engine sizes as low as 15hp gives significant savings in fuel costs.

The DS18 is available in 4 versions with one motor boat. The wide and spacious 2.2m (7'2") full beam enables a deck area of 75m2 (800) square feet, fish hold capacity of 3.2m2 (112cu ft) and a carrying capacity of three tons. The MFV version can be fitted with long bite keels for difficult launching conditions or the shorter standard bilge keel for harbour use. When dried out the DS18 will stand almost upright. There are 3 cabin options:-

  • Full forward traditional Cornish
  • Forward offset;
  • Aft pillbox style

The Treeve DS18 is fitted with our standard heavy duty galvanised irons made from 3/8" plate and 1/4" lugs. Timber keels for beach launching may be added. There is ample room forward of the inboard diesel engine to fit an hydraulic pump and equipment. The deck may be self draining or loose board depending on preference on preference. The steering may be either underhung steel semi balanced or traditional transom hung timber rudders.

DS18 SPECIFICATIONS

Dimensions

Overall length: 5.52m (18'3")
Beam 2.13m (7')
Draught 0.65m (2'6")
Deck area 75m2 (800sq ft)
Hold capacity 3.2m3 (112 cuft)

Construction

Hull lay-up

13oz laminate made up as follows:-
1 gel coat. pigmented throughout or clear below waterline as preferred 
1 x 2oz CSM and 6 x 2oz CSM
Transom reinforced: lay-up 2 x 2oz CSM
Sheerline reinforced: Lay-up 2 x 2oz CSM
Keel joint reinforced 1 x 1oz CSM and 5 x 2oz CSM
Transverse frames and longtudinals 75x50mm (3x2") polyurethane expanded foam encapsulated by 3 layers x 2oz CSM, staggered
Timber inserts on sheerline
Beam shelf as above according to customers own requirements

Floorboards

20mm (3/4") Marine ply or 32mm (1 1/4") loose pine boards to customers preference

Engine beds

Hardwood 1 1/2 x engine length set in longitudinal foam stringers
Fore and aft encapsulated in 8oz GRP

Rudder

Hardwood

Recommended engines

Recommended 22 - 30hp

Other equipment

Bilge pump, fairleads. Safety equipment to customers requirements
 

FOR MORE INFORMATION, PLEASE CONTACT US.

 

ALL MEASUREMENTS, SIZES AND WEIGHTS ARE APPROXIMATE. ALL PLY IS MARINE PLY. HULL LAMINATE AND FRAMING TO SFIA AND LLOYDS SPECIFICATIONS (OR BETTER) WITH RESPECT TO MATERIALS AND FRAME SPACING USED. ALL PHOTOS ARE FOR ILLUSTRATION PURPOSES ONLY. TREEVE BOATS IS COMMITTED TO A PROCESS OF CONTINUOUS PRODUCT DEVELOPMENT AND THE SBOVE SPECIFICATION MAY BE MODIFIED AND DOES NOT FORM PART OF ANY CONTRACT. THE ACTUAL VESSEL, FINISH AND FITMENTS WILL BE AS AGREED WITH THE CUSTOMER AT TIME OF ORDER. E&OE.